China Low Power Anti Intrusion Fail Safe Bolt Lock for Fully Frameless Glass Door power lock and release tailgate
Electric Bolt for Full Frameless Glass Door: Adopt high quality materials, stable & reliable, DC12V, ZDL-5818 is specially designed for frameles glass doors (without up & down frame), used by matching a bracket, and is convenient to match with automatic door. Time delay setting can keep the bolt open/close status in a certian period. So when it connects to access control, it can make some employee enter or exit the door simultaneously. It also can check the position of lock and door.
– Optional model: ZDL-5818S: Size: L148xW43xH39(mm), Stailess steel, Power-off to open Packing size:18.5X10.5X6CM,1.3KG
– it’s specially used for full frameless glass door (without up & down frame) – Safety mode: Power-on to lock; Power-off to open( fail safe). – Adjustable delay: 0 Second, 2.5 Seconds, 5 seconds optional. – With NO /NC output(Connect NC, fail safe; Connect NO, fail secure). – Signal output: Door state, Lock state.
Using a power lock in your vehicle allows you to lock the doors without having to take your hands off the wheel. It is also great for front passengers to use.
Among the most common features on any vehicle are power door locks. These locks work by turning a gear mechanism and lock or unlock the door. The gear mechanism is made of an electric motor and spur gears. Power door lock actuators are critical to the operation of a power door lock feature. When a power door lock actuator fails, it disables the power door lock feature. The most common complaint about a power door lock actuator is that it locks and unlocks intermittently. This may be due to a problem with the wiring or circuits. Some symptoms of a faulty power door lock actuator are noises coming from inside the door. For example, when a motor is not turning, it will make a loud “clunk” sound. When a motor is working properly, there will be little or no noise. A faulty power door lock actuator may also cause a car to lock and unlock randomly. This can happen due to a faulty circuit or circuits wearing out. Alternatively, a faulty actuator may be the result of a water leak in the door. If this is the case, the water may enter the door lock actuator and cause it to malfunction. Fortunately, there are a number of ways to check the condition of your actuator and fix any problems.
Almost all modern day cars have some form of power lock, but only a select few have a body controller to boot. The fancy name is the electronic control unit, but the acronym ECU stands for Electronic Control Unit, or ECU for short. The ECU is responsible for coordinating the myriad electronic components that are dotted throughout your vehicle’s occupant compartment. It also controls things like power windows and the air conditioning. You can see the ECU in action by glancing at your dashboard. It’s a small and power-packed box, but a discerning eye will spot a few stragglers amongst the more mundane tasks. The ECU is also responsible for ensuring the safety of passengers by ensuring that the doors remain unlocked until a specified interval. The ECU’s lesser known cousins, like the power door lock, are only responsible for a few of the more mundane tasks. Aside from the usual suspects, the ECU also manages the power mirrors and the power windows, albeit on a less than optimal schedule. A faulty ECU isn’t quite as funky as it sounds, and can be rectified by a trip to the local mechanic. If you’re not a mechanic, you’ll likely be able to remedy the situation with a simple door lock replacement.
Check for broken wires
Occasionally, you will need to check for broken wires when using a power lock. Having a broken wire will require you to repair it, or replace it with a new one. However, this process can be quite difficult, as it is hard to reach the motor. If you are unsure what wires are connected to your vehicle, you should consult a wiring diagram. If you do not have a diagram, you can also use a multimeter to check for continuity across all wires. However, a multimeter is not enough to check for broken wires. You will also need rubber gloves to do this safely. To check for broken wires, first make sure you have access to the wires that are in the lock motor. These are usually located near the plug on the door frame. If you can’t reach them, you can use jumper wires to connect the actuator to the 12 volt power supply and test it for power. If this does not work, you will need to remove the lock motor from its electronic control board and check for a broken wire harness. However, if this is not possible, you can use a Power Probe to apply 12 volts to the actuator.